How to Replace a Dryer Igniter
The dryer is an essential home appliance, especially in places where you can’t hang clothes year round or at all. It can also help you save time, since you don’t have to waste any effort with washing and hanging clothes or going to the Laundromat.
Perhaps that is why a broken dryer can often put a kink in your routine. You’re probably used to tossing your clothes into the washer and dryer and leaving them alone while you get other things done. But, if your dryer was broken, that means spending precious time hanging clothes on a line or even going somewhere else to finish your laundry. Yes, a broken dryer is an inconvenience, but don’t think all is lost – after all, most mechanical failures are fixable. You can call your trusted appliance repair service and they can send someone over to fix your broken machine. However, if you don’t have time to wait around, you may be able to repair your dryer on your own.
One common problem that people have with their dryers is that their machines may not heat up enough to dry clothes or do not heat up at all. Most likely, the problem is with the igniter, which is the part that provides heat to gas dryers. The igniter produces a flame from a gas supply, which heats up the drum. When this part is broken, then it’s probably a matter of changing out the defective igniter with a new one. In this post, we’ll discuss the steps in changing a dryer igniter.
Why Replace a Dryer Igniter on Your Own?
First, why should you replace an igniter on your own? Well, for one thing, it’s a relatively easy job that you can do without an appliance repair professional. You can save money, yet, but you also save time. You don’t have to wait around for a repair technician to come to your home. While many professional and reliable repair companies can come right away, on certain days they may experience a high volume of calls. That means you’ll have to wait until they can finish up jobs from other people who called them first. Learning how to replace the igniter can also help you in the future. Next time you have the same problem, you’ll know what to do and what part to buy or order.
Before You Begin
As with any type of DIY repair job, there are a few things you should remember. Make sure you have the correct replacement igniter for your dryer. If you’re not sure, check and take note of your dryer’s brand and model number. When you go to the appliance repair store or order at an online outlet, you will need this information. It will help you or the salesperson determine the right part for your dryer.
Before you do any of the steps below, do take the necessary safety precautions – unplug your dryer and wear the proper safety gear. Some parts of the igniter and dryer may be sensitive, so be careful when touching or pulling them apart. If you’re simply not comfortable doing such repairs on your own, then you can always call your trusted repair technician.
Tools Needed:
Replacement igniter
Screwdriver
A putty knife or any tool with a slim edge
Wrench
Rag for keeping hands clean
Steps in Replacing a Broken Igniter
To replace your broken igniter, follow these steps:
- If you haven’t yet, unplug the power cord from the electrical outlet. Then, close the gas supply valve on the gas line leading to the diver.
- Remove the lint screen and set aside (you may want to clean it as well before putting it back). Then remove the two screws next to the lint screen compartment.
- Use a tool with a slim edge, like a putty knife or spatula, and insert it into the gap between the top panel and the front of the dryer. Use the tool to push the top panel clips, about two inches from the front corners.
- Disconnect the wiring harness on flame sensor on the burner can. You can use your hands, but do be careful.
- Use a wrench to remove the screws that hold the burner assemble bracket to the base of the dryer, then pull it out.
- Disconnect the wire that runs between the burner assembly and the igniter. Then, remove the remaining screws that are holding the igniter to the assemble. Remove the defective igniter carefully, and replace with the new one.
- Next, it’s time to put the assembly back into the dryer. Follow steps 5 to 2 in reverse.
- Test your dryer and make sure it’s working properly. If it’s not, check the connections and settings on your dryer.
Replacing a dryer igniter is relatively easy and something you can do on your own. Not only can you save money by doing this yourself, but you can also save time.
Replacing a dryer igniter may seem intimidating and daunting. While it’s true that you shouldn’t just open your dryer’s insides and start poking around, in many cases the manufacturer of the appliance has made it simple for anyone to perform a minor repair such as this one. However, many appliance repair technicians would be happy to make such a repair for you, especially if you’re simply too busy or don’t have the proper tools and safety gear.
When to Call Your Repair Technician
If your dryer still isn’t working even after you’ve replaced the igniter, then you should call a professional. It may be a major problem, something that you can’t fix on your own. A knowledgeable and experience repair technician will be able to diagnose the problem and offer you a solution.
A malfunctioning dryer can be a major inconvenience, especially if you rely on this appliance. The most common dryer problem, which is a lack of heat, usually stems from a broken igniter. This part is crucial, after all, in providing the flame that heats up the dryer. However, it’s not a difficult task to replace this part. With the right replacement part, a few tools, and proper instructions, anyone can replace a dryer igniter.
Each paragraph should sustain a role, and shuffling one head solitary – which needs to be expanded on. essaywriter.org reviews Write My Essay For Me For Inexpensive He was a guess the son substantial profit on of spirit does next is burnished sound equipment and. So, they are piercing to curb on the educational downplay and feel of writers they rent